public Class LauncherConstants

Default maximum number of bytes for buffering to use per thread and output type if output capturing is enabled.

See Also

CAPTURE_MAX_BUFFER_PROPERTY_NAME

Property name used to configure the maximum number of bytes for buffering to use per thread and output type if output capturing is enabled:

Value must be an integer; defaults to 4194304.

See Also

CAPTURE_MAX_BUFFER_DEFAULT

Property name used to enable capturing output to System#err:

By default, output to System#err is not captured.

If enabled, the JUnit Platform captures the corresponding output and publishes it as a ReportEntry using the stderr key immediately before reporting the test identifier as finished.

See Also

STDERR_REPORT_ENTRY_KEY, ReportEntry, TestExecutionListener#reportingEntryPublished(TestIdentifier, ReportEntry)

Property name used to enable capturing output to System#out:

By default, output to System#out is not captured.

If enabled, the JUnit Platform captures the corresponding output and publishes it as a ReportEntry using the stdout key immediately before reporting the test identifier as finished.

See Also

STDOUT_REPORT_ENTRY_KEY, ReportEntry, TestExecutionListener#reportingEntryPublished(TestIdentifier, ReportEntry)

Property name used to configure the critical severity of issues encountered during test discovery.

If an engine reports an issue with a severity equal to or higher than the configured critical severity, its tests will not be executed. Depending on DISCOVERY_ISSUE_FAILURE_PHASE_PROPERTY_NAME, a org.junit.platform.launcher.core.DiscoveryIssueException listing all critical issues will be thrown during discovery or be reported as engine-level failure during execution.

Supported Values

Supported values include names of enum constants defined in Severity, ignoring case.

If not specified, the default is "error" which corresponds to Severity.ERROR).

Wildcard pattern which signals that all listeners registered via the ServiceLoader mechanism should be deactivated:

See Also

DEACTIVATE_LISTENERS_PATTERN_PROPERTY_NAME, org.junit.platform.launcher.TestExecutionListener

Property name used to provide patterns for deactivating listeners registered via the ServiceLoader mechanism:

Pattern Matching Syntax

If the property value consists solely of an asterisk (*), all listeners will be deactivated. Otherwise, the property value will be treated as a comma-separated list of patterns where each individual pattern will be matched against the fully qualified class name (FQCN) of each registered listener. Any dot (.) in a pattern will match against a dot (.) or a dollar sign ($) in a FQCN. Any asterisk (*) will match against one or more characters in a FQCN. All other characters in a pattern will be matched one-to-one against a FQCN.

Examples

• *: deactivates all listeners.
• org.junit.*: deactivates every listener under the org.junit base package and any of its subpackages.
• *.MyListener: deactivates every listener whose simple class name is exactly MyListener.
• *System*, *Dev*: deactivates every listener whose FQCN contains System or Dev.
• org.example.MyListener, org.example.TheirListener: deactivates listeners whose FQCN is exactly org.example.MyListener or org.example.TheirListener.

Only listeners registered via the ServiceLoader mechanism can be deactivated. In other words, any listener registered explicitly via the LauncherDiscoveryRequest cannot be deactivated via this configuration parameter.

In addition, since execution listeners are registered before the test run starts, this configuration parameter can only be supplied as a JVM system property or via the JUnit Platform configuration file but cannot be supplied in the LauncherDiscoveryRequest} that is passed to the Launcher.

See Also

DEACTIVATE_ALL_LISTENERS_PATTERN, org.junit.platform.launcher.TestExecutionListener

Property name used to configure the phase that critical discovery issues should cause a failure

Supported Values

Supported values are "discovery" or "execution".

If not specified, the Launcher will report discovery issues during the discovery phase if Launcher#discover(LauncherDiscoveryRequest) is called, and during the execution phase if Launcher#execute(LauncherExecutionRequest) is called.

Property name used to enable dry-run mode for test execution.

When dry-run mode is enabled, no tests will be executed. Instead, all registered TestExecutionListeners will receive events for all test descriptors that are part of the discovered TestPlan. All containers will be reported as successful and all tests as skipped. This can be useful to test changes in the configuration of a build or to verify a listener is called as expected without having to wait for all tests to be executed.

Value must be either true or false; defaults to false.

Property name used to enable support for LauncherInterceptor instances to be registered via the ServiceLoader mechanism:

By default, interceptor registration is disabled.

Since interceptors are registered before the test run starts, this configuration parameter can only be supplied as a JVM system property or via the JUnit Platform configuration file but cannot be supplied in the LauncherDiscoveryRequest} that is passed to the Launcher.

Property name used to configure the output directory for reporting.

If set, value must be a valid path that will be created if it doesn't exist. If not set, the default output directory will be determined by the reporting engine based on the current working directory.

Placeholder for use in OUTPUT_DIR_PROPERTY_NAME that will be replaced with a unique number.

This can be used to create a unique output directory for each test run. For example, if multiple forks are used, each fork can be configured to write its output to a separate directory.

Property name used to enable or disable stack trace pruning.

By default, stack trace pruning is enabled.

Key used to publish captured output to System#err as part of a ReportEntry:

Key used to publish captured output to System#out as part of a ReportEntry: